Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Metal Roof Installation Cost in Fresno, CA? (2026 Price Guide)
Metal roof installation in Fresno typically costs $14,500 to $38,000 for a standard single-family home, with most homeowners paying around $22,000 to $28,000. The price works out to roughly $9 to $18 per square foot installed, depending on the metal type, roof pitch, and whether the old roof needs to come off first. A standing seam roof (the premium option) runs higher than a corrugated or ribbed metal panel system.
This price guide breaks down what we actually see on rooftops in Fresno right now, not national averages pulled from a database. We are Brennan Roofing Co Fresno, and we put every price on paper before any work starts.
Key Takeaways: Metal Roof Costs in Fresno
- Full metal roof replacement: $14,500 to $38,000 depending on home size and metal profile
- Per square foot: $9 to $18 installed, including tear-off when needed
- Standing seam: $13 to $18 per square foot; this is the top-tier metal option
- Corrugated or ribbed panels: $9 to $13 per square foot
- Larger roofs cost less per square foot because setup and mobilization spread across more area
- Fresno summer heat adds a wrinkle: metal roofs here need proper underlayment for thermal movement, which affects cost
Metal Roof Installation Cost Breakdown (2026)
Here are the line-item price ranges for the Fresno market. These numbers reflect what we quote on this page before any work begins, so you can budget without having to call just to get a ballpark.
| Cost Component | Price Range (Fresno, 2026) | What It Covers |
|---|---|---|
| Tear-off of existing roof | $2,000 to $4,500 | Removal and disposal of old shingles, tile, or existing metal. Fresno landfill and haul-away fees are already baked in. |
| Decking repair or replacement | $1,500 to $4,000 | Replacing rotted or damaged plywood decking before the metal goes down. Older homes in the Tower District and Fig Garden often need some deck work. |
| Underlayment | $0.50 to $1.50 per sq ft | The water-shedding barrier between the deck and the metal. Standing seam systems typically use a high-temperature rated synthetic underlayment here because Fresno attics get brutally hot. |
| Corrugated or ribbed metal panels | $5 to $8 per sq ft (materials only) | The metal itself. This is the workhorse option: exposed fasteners, simple profile, solid performance. |
| Standing seam panels | $8 to $12 per sq ft (materials only) | Hidden fasteners, raised vertical seams. The premium metal roof that performs best long-term in Fresno’s heat-cycling climate. |
| Flashing and trim | $800 to $2,500 | Metal flashing at valleys, chimneys, skylights, and roof-to-wall transitions. Flashing is the thin metal that directs water where it should go; it is the difference between a roof that leaks and one that does not. |
| Drip edge | $400 to $1,200 | The metal strip along the roof’s edge that keeps water from curling back under the metal and onto the fascia. |
| Labor and installation | $4,000 to $10,000 | The crew’s time. Metal takes longer than shingle because every panel is cut to the roof, and the fastening pattern matters in Fresno’s wind and heat. |
| Permit and inspection | $450 to $1,200 | City of Fresno permit fees and the required inspection. Every metal roof in Fresno needs a permit; a roofer who skips it is not saving you money, they are handing you a lien risk. |
For a 1,800 square foot single-story ranch in Woodward Park or a two-story in Sunnyside, the all-in number lands between $16,000 and $32,000 for most standing seam projects. The lower end reflects a straightforward roof with few penetrations and no decking surprises. The higher end reflects steep pitches, multiple valleys, skylights, or a roof that needs substantial decking replacement once the old material comes off.
Standing Seam vs. Corrugated: The Real Cost Difference
Standing seam runs roughly 30 to 40 percent more than corrugated or ribbed metal. Why the gap? It is not all looks. Standing seam uses hidden fasteners, which means no exposed screws with rubber washers that degrade in Fresno’s UV-heavy summers. The panels lock together and float on clips that allow the metal to expand and contract without working the fasteners loose. On a 110-degree August afternoon, a metal roof can move measurably. Standing seam handles that movement better, and in the Fresno market that is not a luxury, it is an engineering consideration.
Corrugated metal still works here. We install both, and we will give you the straight breakdown of what each means for your house when we put the written estimate in your hand. We source from leading manufacturer lines including GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral, so the conversation is about which material actually fits your roof, not which one we happen to have in the yard.
What Affects Metal Roof Installation Pricing in Fresno
Every roof is different, but here are the six factors that move the number most in this market.
- Roof pitch. Steep roofs in the Old Fig Garden area with 8/12 or 10/12 pitches cost more because the crew works slower, needs more safety equipment, and often requires staging. A 4/12 ranch roof out in Clovis costs less per square foot because access is straightforward.
- Existing roof material and condition. Tearing off concrete tile costs more than tearing off asphalt shingles. Tile is heavy, and disposal fees in Fresno run higher for tile. If your decking underneath is shot, that cost stacks on top.
- Roof complexity. Every valley, dormer, chimney, and skylight adds flashing labor. Flashing is the thin metal that directs water at transitions, and it is where most roof leaks happen. A roof with six penetrations costs more than a clean rectangle, and that money is well spent.
- Metal panel profile and gauge. Thicker metal (24-gauge vs 26-gauge) costs more but resists denting during Fresno’s occasional hail events. Standing seam with hidden fasteners costs more than exposed-fastener panels.
- Home size, but not linearly. A 3,000 square foot roof costs more total than a 1,500 square foot roof, but the per-square-foot number drops because setup, dump fees, and mobilization spread across a bigger job.
- Underlayment requirements. Metal roofs in the Central Valley need underlayment that handles high temperatures. A standard synthetic underlayment rated for 180 degrees costs less than a high-temp product rated for 240 degrees, but in a Fresno attic the cheaper one can break down faster.
How Much Does a Metal Roof Cost Per Square Foot in Fresno?
As of 2026, the installed cost in Fresno runs $9 to $13 per square foot for a corrugated or ribbed metal roof and $13 to $18 per square foot for a standing seam system. Those numbers include materials, labor, underlayment, flashing, drip edge, and standard tear-off. They do not include major decking replacement or structural repairs, which get quoted separately once the old roof is off and we can see what is actually underneath.
In North Fresno neighborhoods like Bullard and Herndon Avenue corridor homes from the 1980s and 1990s, we often find the original plywood decking is fine and the total lands on the lower end. In older neighborhoods like the Tower District, where homes date to the 1920s, decking surprises are more common.
Is Metal Worth the Higher Upfront Cost in Fresno?
The honest answer: it depends on how long you plan to stay in the house. A metal roof costs two to three times what an architectural shingle roof costs in Fresno. In exchange, the metal roof lasts 40 to 70 years versus 20 to 30 for shingles. If you plan to stay in the house for 15 years or more, metal typically wins on total cost of ownership. If you are selling in five years, you will not recoup the difference at resale.
There is also the heat factor. Metal reflects solar radiation better than asphalt shingles, which absorb it. In a Fresno summer, a metal roof can keep the attic 10 to 20 degrees cooler. That directly reduces air conditioning load during the months when PG&E bills spike. Homeowners throughout the San Joaquin Valley have documented this effect for years. The savings are real, though they take years to fully offset the higher material cost.
For a more detailed look at the process, see our page on Metal Roof Installation in Fresno.
How to Save on Metal Roof Installation
Here are practical ways to bring the number down without cutting corners that will cost you later.
- Get the roof measured properly the first time. An accurate measurement prevents over-ordering of metal panels, which means you pay for what goes on your house, not what sits in the yard. Our written estimate is based on a real measurement, not a satellite image.
- Time the project in the off-season. Roofing in Fresno runs year-round, but late fall and early winter are lighter for most crews. Prices do not change dramatically, but scheduling is faster and crews are less rushed.
- Replace decking only where needed. Some roofers quote full decking replacement sight unseen. We write the decking estimate based on what we can see, and if the old roof comes off and the deck is solid, you pay for what was actually replaced, not a worst-case estimate.
- Choose the right metal profile for your actual needs. Corrugated is not a downgrade. If your roof has few penetrations, low pitch, and you want 40 years of performance without standing seam pricing, it is a legitimate choice. We will show you both and let you decide with numbers on paper.
- Understand the guarantee before you sign. Every Brennan Roofing job carries the 365-Day Done Right Promise: if it is not done right, we make it right, in writing, at no charge. A roofer who will not put that on paper is pricing you a different kind of risk.
The best way to save is to get a free estimate that gives you the real number for your specific roof. Call (559) 785-2160 and we will put the price on paper before any work starts.
FAQs – Metal Roof Installation Cost
How much does a metal roof cost on a 1,500 square foot home in Fresno?
A 1,500 square foot single-story home in Fresno typically costs $13,500 to $27,000 for a full metal roof installation in 2026. Corrugated metal on that footprint runs $13,500 to $19,500; standing seam runs $19,500 to $27,000. The spread accounts for tear-off, decking condition, and roof complexity. Call (559) 785-2160 for an exact quote on your address.
Is it cheaper to repair or replace a metal roof in Fresno?
Repair is cheaper in the short term: fixing isolated panel damage or a failed flashing runs $300 to $1,500 depending on what failed. But if the roof is more than 25 years old and you are repairing it more than once a year, replacement becomes the better financial call. Every Brennan Roofing repair carries the same 365-Day Done Right Promise as a full installation, in writing, for a full year, with a free return visit if it fails.
How much does it cost to replace a metal roof with a new metal roof?
Metal-over-metal replacement in Fresno runs $14,000 to $34,000 for a typical single-family home. The old metal must come off first; we do not recommend laying new metal over old because trapped moisture and rust between layers shorten the life of the new roof. Tear-off of metal costs slightly more than shingle tear-off because of fastener removal and metal recycling requirements.
Can you install a metal roof in Fresno in the summer?
Yes. Fresno metal roofing crews are used to working in 100-degree heat, and we schedule early starts to beat the worst of the afternoon sun. The material itself handles the heat fine; proper handling matters more than the calendar. The only weather we pause for is rain, and Fresno bare skies handle that concern most of the year.
How long does a metal roof installation take?
Most Fresno metal roof installations take 3 to 7 working days from tear-off to final inspection. Standing seam takes longer than corrugated because every panel is custom-cut and seamed on site. Your written estimate includes a start window and a completion target, and our technicians show up inside the promised window, in uniform, with background checks completed before they ever set foot on your roof.
Does a metal roof require a permit in Fresno?
Yes. The City of Fresno requires a building permit for roof replacement, including metal. Permit and inspection fees of $450 to $1,200 are included in our estimates. Skipping the permit saves a few hundred dollars up front and creates problems when you sell, refinance, or file an insurance claim. We pull permits on every job.
Why Brennan Roofing Quotes the Way We Do
The Garrison Standard is the operating rule at Brennan Roofing. It is not a slogan; it is the process every job follows. The price goes on paper before any work begins. The number on that paper does not move at the door. Our technicians are background-checked, they arrive in uniform, and they show up inside the window we gave you. Our phones are answered by a live person around the clock, no voicemail, no automated system.
Brennan Roofing is part of the Garrison Partners family, founded in 2000, and this Fresno location is independently owned and operated to the same Garrison Standard. Travis Oakley leads the team here. We install metal roofing using materials from GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral. We will explain the trade terms, the material options, and the numbers in plain language so you can choose with confidence. Every job is backed by the 365-Day Done Right Promise, in writing, for one full year.
Get Your Written Metal Roof Estimate in Fresno
If you are ready to know what a metal roof costs for your specific home, call (559) 785-2160. We will schedule a measurement, answer your questions straight, and hand you a written price before any work starts. No pressure, no vague numbers, no price that changes at the door. That is how the Garrison Standard works.
Pricing reflects the Fresno market as of 2026. Brennan Roofing Co Fresno offers free estimates – call (559) 785-2160.
Written by Travis Oakley, Owner at Brennan Roofing Co Fresno, serving the Fresno area under the Garrison Standard.
What Our Customers Say
"Honest inspection with photos. Told me I only needed a repair, not a replacement."
- Sergio P."Neat, quiet, and disciplined crew. Magnet swept the yard after."
- Tonya R."Storm took off a section of shingles. They were here next morning to tarp it and finished the repair that week."
- Elaine D.